How to drain down a water system
Turn off the stopcock and the boiler, open every cold tap from the top floor down, then flush each toilet once. That empties most of the water left in the pipes so a burst stops leaking.
- Call or tap to start
What's the job?
Tap one to start, or call us if water is coming through now.
Get my priceor call 020 3927 3001
Draining the cold water step by step
Step 1
Turn off the stopcock
It is usually under the kitchen sink. Turn it clockwise until it stops.
Step 2
Switch off the boiler and immersion heater
Use the boiler's switch or fused spur. They must not run with the water going. If water is near light fittings, sockets or the fuse box, switch off at the consumer unit first, but only if you can reach it without standing in water.
Step 3
Open the cold taps from the top down
Start with the highest tap in the house and work down. The kitchen cold tap is normally fed straight from the mains and drains first.
Step 4
Flush every toilet once
Do not keep flushing. The cisterns will not refill with the water off.
Step 5
Leave the taps open, then close them
Wait until each tap stops running, then close it, so you will notice when the water comes back on.
Why drain down at all
Turning off the stopcock stops new water coming in, but the pipes are still full. A burst on an upstairs pipe will keep running until what is in the pipes, and any tank in the loft, has emptied through the split.
Draining down sends that water out through your taps and toilets instead, where it does no harm. It is also a standard way to protect an empty home from frozen pipes in winter.
If you have a tank in the loft
Older houses often have a cold water storage tank in the loft feeding the bathroom taps, the toilets and the hot water cylinder. The stopcock stops the tank refilling, but the tank itself can still empty through a burst.
Running the bathroom cold taps and the bath taps will empty it. If the burst is between the tank and the taps, look for a gate valve (a round wheel valve) on the pipe coming out of the tank. Closing that isolates the tank.
The drain-off valve, leave it to a plumber
Do
- Use the taps to empty the pipes in an emergency, as they do the job well enough.
- Know where your drain-off valve is: a small valve near the stopcock or at the lowest point of the pipework.
- Call a plumber if you want the pipes emptied completely.
Don't
- Open the drain-off valve without a hose fitted and run to a drain, or it empties onto your floor.
- Force an old valve, as some refuse to close again.
- Work on the safety valves of an unvented cylinder yourself.
Combi boiler or hot water cylinder?
With a combi boiler there is no stored hot water. Once the cold is off and the boiler is switched off, opening the hot taps releases only the little water left in the hot pipes.
With a hot water cylinder, usually in an airing cupboard, the cylinder holds a lot of hot water. Open the hot taps only to let the pressure off and empty the pipes. Do not try to drain the cylinder itself in an emergency.
- Draining a cylinder needs its drain-off valve, a hose and somewhere safe for very hot water to go.
- An unvented (pressurised) cylinder has safety valves that only a qualified installer should work on.
- A drained cylinder must be refilled before the immersion heater or boiler is switched back on, or the element can burn out.
Turning the water back on
Step 1
Wait until the burst is repaired
Only then close all the taps again.
Step 2
Open the stopcock slowly
Turn it a little at a time and listen for air hissing out.
Step 3
Open each tap gently
Let each one run until it flows smoothly, then refill the toilets.
Step 4
Switch the boiler and immersion back on
Only do this when the water is fully back.
What to check after refilling
- Every tap runs smoothly with no spluttering.
- Toilets refill and then stop filling.
- No drips at joints, under sinks or around the repair.
- No new damp patches or stains on ceilings and walls.
- The boiler pressure gauge is not reading low.
- The hot water cylinder is full before any heating switches on.
If the repair changes your pipework
Any new or altered fitting on a mains supply must be of a suitable standard and installed so it does not waste, misuse or contaminate water (the Water Supply (Water Fittings) Regulations 1999). A few kinds of work, such as a bath over 230 litres or a pump drawing more than 12 litres a minute, must be notified to the water company first, which has ten working days to reply.
Who qualifies for Water fittings regulations and notifiable plumbing work
- Applies to fittings connected to a water company's supply in England and Wales.
How to apply
- 1Check whether the work is on the notifiable list.
- 2Send notice to your water company with the details, plan and pipework diagram it asks for.
- 3Wait for consent or ten working days before starting.
Source: The Water Supply (Water Fittings) Regulations 1999, regulation 5, checked 2 November 2026
More questions
How long does it take for the pipes to drain?
The mains-fed kitchen tap usually runs dry first. A loft tank and long pipe runs in a bigger house take longer. Leave the taps open until each one has stopped.
Should I drain the system if I am going away in winter?
If the home will be empty and unheated in freezing weather, draining down is a sensible precaution. Leaving the heating on low is the other option. Either way, know where your stopcock is before you go.
Can I drain the hot water cylinder myself?
It is best left to a plumber. The water is very hot, the drain-off valve needs a hose run to a drain, and unvented cylinders have safety valves that need a qualified installer.
Will draining the system damage my boiler?
Not if the boiler is switched off first. A combi boiler should not be run with no water coming in, and a system with a cylinder should be refilled before anything heats it again.
Related
Where we work
Deptford and the areas around it. Every postcode listed is in our area.
Boundaries: Office for National Statistics (OGL v3.0). Contains OS data © Crown copyright and database right 2024.
- DeptfordSE8
- New CrossSE14
- GreenwichSE10 SE18 SE9 SE3 SE7 SE28 SE2
- LadywellSE13
- LewishamSE13 SE6 SE23 SE26 SE8 SE4 SE14 SE12
- BrockleySE4
- RotherhitheSE16
- PeckhamSE15 SE5
- NunheadSE15
- Hither GreenSE13
- CatfordSE6 SE13 SE4
- LeeSE12
- BermondseySE1
- East DulwichSE22
- WalworthSE17
- CharltonSE7
- Forest HillSE23
- CamberwellSE5
Want it sorted for you?
Tell us what's going on and we'll price the job.
- Call or tap to start